1. BACKGROUND

The purpose of this lesson is to provide background prototype information in support of the lessons on the installation of ORR HO scale Street Railway Track. Since for all practical purposes traditional street railway track has virtually disappeared from most of North America, it is necessary to review some of the peculiarities that were encountered in the development and installation of track in city streets before trying to replicate this in models. In modeling, we are restricted by many factors so compromises have to be made. Trolleyville feels that modelers should be aware of the prototype make the best modeling compromises and decisions.

2. PROTOTYPE GIRDER RAIL

Prototype Girder rail, two examples of which are shown below is different from the 'T' rail commonly used in railroads and was invented to eliminate damage to wheels from street paving materials such as cobblestones, Belgian block, concrete, macadam and asphalt. The rail contained an integral flangeway and also served as an I-beam that did not flex under the weight of the streetcars and cause damage to the adjacent pavement. Such rail is still available in Europe as tram rail. Girder rail was extremely durable, lasting in many grade crossings in Southern California almost 30 years past the departure of the Pacific Electric. The guardrail, when added, formed a type of rail that we will call girder "High Guard" rail. This “High Guard” rail is normally used for curves, at crossings and at turnouts. Richard Orr gave the HO scale modeler a relatively easy opportunity to model girder rail installations with the track he developed in the 1980s. This track is now available from Custom Traxx (http://www.customtraxx.com)

Some photos of Girder Rail compared to T-Rail are shown below. The next photos were taken in Hawthorne, October 2003.

3. OGIVE SHAPED CURVES

Many prototype curves, especially the sharp curves found in east coast city streets where streets were narrow, were not of uniform radius as is commonly the case of the "snap" track that is originally used by all modelers. These curves tended to be ogive shaped with the smallest radius in the center and easements at the ends. This helped the clearance situation in tight places and eased the car into the curve with a more gradual motion. Streetcars tended to have tapered ends to minimize clearance problems with other cars at these curves. In this lesson, we will begin by installing constant radius curves. But there will be at least one ogive curve installed. Directly below is a Philadelphia Rapid Transit track diagram for the intersection of 9th and Chestnut that we obtained from Charles Long, an avid traction modeler who is a member of the East Penn Traction Club. This clearly shows the ogive shape of the curve.

During this investigation into streetcar curves, we discovered that most of the streets in center city Philadelphia were not laid out at exactly right angles. Note on the above drawing that the crossing angle is 89 degrees, 40 minutes. We understand this problem was corrected by the time that streets in North and West Philadelphia were laid out. But, note the variance in the radii of the curve. The points start at 200 ft radius (27 inch radius in HO scale) and graduates down to 72' radius (10 inch radius in HO scale), then the curve goes to 60 ft radius (8 inch radius in HO scale)and then to 36 ft (5 inch radius in HO scale). The middle one-third of the curve is 33' radius (4.5-inch radius in HO scale). The photograph below, courtesy of an Ed Miller photograph, shows a similar curve at 15th and Arch in 1954. Notice the gradual, almost straight portion of the curve at the switchpoints. Also notice how close the car is to the curb as it turns. Without the ogive shaped curve, the center of the car would have struck people standing on the curb waiting to cross the street.

The next view shows the portion of the curve that is under the car in the above photo. The car in the above photo is an unmodernized 8000 series Peter Witt taking a short turn on Route 48. The car would have normally turned left and proceeded eastbound to Front & Arch. The car in the photo below is another unmodernized 8000 series Peter Witt car eastbound on either route 9 or 33.

4. DEVIL STRIPS

The space between double tracks was popularly called a "devil" strip since there was very little room between passing cars in some cases. Many an accident would occur there if you were in the wrong place at the wrong time. Note how narrow the "devil strip" was on Arch St. in the above photo. Keep in mind that Philadelphia track gauge is 62 1/4" and the cars were no more than 100" wide. The next photo was taken on August 18, 1933 as a result of an accident. It was used to demonstrate that there was only 5.0 inches clearance between passing streetcars on Ridge Avenue at School Lane. This is the main reason for bars and/or grates on the sides of the cars. Both cars in the photo are the famous Philadelphia Nearside cars, of which there were 1500 at one time.

Of course there were wider devil strips, especially in cities that used "boulevard poles" between such double tracks to support the overhead wire, as is currently the case on St. Charles Avenue in New Orleans. Incidentally, route 61 was converted to trackless trolleys and continued in that fashion until the 1960's.

5. MODELING OGIVE CURVES

Returning to our plan of 9th and Chestnut (below) and superimposing a 6 1/8" radius curve (red dashed lines) on the plan, the tracks are really close to the curb and any car using that curve could strike a lot of people on the sidewalk. The city fathers and anyone on that street corner would not have liked that track location at all. The use of the ogive curve moved the track five feet farther from the curb. Note illustration below:

Using ORR turnouts and girder rail with 6 1/8" radius curves (44.4 ft radius) would result in the track shown in red. Detail on construction of this type of curve is contained in Parts 2 and 3 of the ORR TRACK lessons.

6. "NON-CLEARANCE" CURVES

Many prototype double track curves in city streets were "non-clearance" curves. This means that two streetcars could not pass on these curves without hitting each other. In some cases, this must be the case in modeling, but should be avoided as much as possible, especially on club layouts where inattention could cause a model to be seriously damaged. In most of these cases, when the tracks were originally installed, short four-wheel cars were used which could pass each other. When the double track cars came, the problem existed and they were slowly eliminated as track replacement occurred. Such activity happened again as recently as the 1980s when Philadelphia replaced PCC cars with the longer Kawasaki LRTs.

7. MODELING LIMITATION IN HO SCALE

Currently in HO scale, standards permit much larger flanges than prototype so girder rail flangeways are larger. This forces switchpoints to be larger and some track plans will be dramatically affected. Keep this is mind, especially in areas where multiple turnouts will be located close together.

8. CURRENT TRACK REPLACEMENTS

For many reasons, most likely unavailability, street car systems remaining in service in North America are using plain T-rail for street track. The area around the track is paved with concrete and the flangeway is formed in such concrete. In October 2010, the trackwork in the entire intersection at 30th & Church in San Francisco was replaced over a three-day period and was captured on a you tube video that is no longer available.

9. FOR MORE INFORMATION

If you really desire to model street railways, check other lessons in the Schoolhouse, especially the ORR TRACK lessons or visit the East Penn Traction Club web site at http://www.eastpenn.org You can email us at orrtrack@customtraxx.com with any questions. When asking questions about proposed track plans, please provide all data, especially a scale drawing of the proposed plan, so that we can answer your questions as accurately as possible. If you live in Southern California, contact the Southern California Traction Club sctc@customtraxx.com The club conducts many workshops on this and other traction related subjects at local Great American Train Shows.